Bend Tool selection names is confusing

New Reply

Thread Rating:

1 Vote(s) - 5 Average
1
2
3
4
5

Share Thread:

Threaded Mode | Linear Mode

Bend Tool selection names is confusing

12-19-2012, 10:42 PM

Post: #16

puzzledpaul Offline

low down bum

Posts: 125
Joined: May 2012

RE: Bend Tool selection names is confusing

Peter - try your object as in post 26, with bend centre being an edge,as shown - but rod top a vert.

Then compare putting rod top one(blue) section away from centre and 5 (blue)sections from centre.

pp

Find

« Next Oldest | Next Newest »

New Reply

Messages In This Thread

Bend Tool selection names is confusing - oort - 12-18-2012, 10:27 PM

RE: Bend Tool selection names is confusing - PeterC (PC) - 12-19-2012, 01:47 AM

RE: Bend Tool selection names is confusing - Fonte Boa - 12-19-2012, 01:59 AM

RE: Bend Tool selection names is confusing - oort - 12-19-2012, 02:25 AM

RE: Bend Tool selection names is confusing - PeterC (PC) - 12-19-2012, 03:33 AM

RE: Bend Tool selection names is confusing - oort - 12-19-2012, 04:16 AM

RE: Bend Tool selection names is confusing - PeterC (PC) - 12-19-2012, 04:17 AM

RE: Bend Tool selection names is confusing - Fonte Boa - 12-19-2012, 11:50 AM

RE: Bend Tool selection names is confusing - oort - 12-19-2012, 03:15 PM

RE: Bend Tool selection names is confusing - PeterC (PC) - 12-19-2012, 08:46 PM

RE: Bend Tool selection names is confusing - Fonte Boa - 12-19-2012, 09:43 PM

RE: Bend Tool selection names is confusing - puzzledpaul - 12-19-2012, 10:30 PM

RE: Bend Tool selection names is confusing - puzzledpaul - 12-19-2012, 10:06 PM

RE: Bend Tool selection names is confusing - puzzledpaul - 12-19-2012, 10:16 PM

RE: Bend Tool selection names is confusing - PeterC (PC) - 12-19-2012, 10:29 PM

RE: Bend Tool selection names is confusing - puzzledpaul - 12-19-2012 10:42 PM

RE: Bend Tool selection names is confusing - PeterC (PC) - 12-19-2012, 10:55 PM

RE: Bend Tool selection names is confusing - puzzledpaul - 12-19-2012, 11:19 PM

RE: Bend Tool selection names is confusing - PeterC (PC) - 12-19-2012, 11:48 PM

RE: Bend Tool selection names is confusing - oort - 12-20-2012, 01:05 AM

RE: Bend Tool selection names is confusing - Fonte Boa - 12-20-2012, 03:09 AM

RE: Bend Tool selection names is confusing - puzzledpaul - 12-20-2012, 04:14 PM

RE: Bend Tool selection names is confusing - oort - 12-20-2012, 11:12 PM

RE: Bend Tool selection names is confusing - puzzledpaul - 12-20-2012, 11:39 PM

RE: Bend Tool selection names is confusing - oort - 12-20-2012, 11:58 PM

RE: Bend Tool selection names is confusing - puzzledpaul - 12-21-2012, 08:45 AM

RE: Bend Tool selection names is confusing - oort - 12-21-2012, 05:41 PM

RE: Bend Tool selection names is confusing - puzzledpaul - 12-21-2012, 06:57 PM

RE: Bend Tool selection names is confusing - oort - 12-21-2012, 09:23 PM

RE: Bend Tool selection names is confusing - puzzledpaul - 12-21-2012, 09:38 PM

User(s) browsing this thread: 1 Guest(s)